Showing results: 3286 - 3300 of 4427 items found.
-
NGY 10GE SFP+ and 10G BASE-T Load Modules -
Keysight Network Applications and Security
Ixia's 10 Gigabit Ethernet LSM10GXM test load modules delivers an industry-leading, high-density, affordable layer 2 through 7, 10 Gigabit Ethernet IP test solution. The NGY family supports both low port count layer 2/3 applications with limited project budgets and highest density test lab, QA, and system test applications. NGY is perfect for both converged data center infrastructure testing and 10GbE switch test beds. NGY load modules leverage Ixia's converged data center test applications to offer the high port scalability, virtual scalability, protocol coverage, with an affordable test solution for data communications testing.
-
MOTOMEA
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
HVST -
Test Electronics
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
PTFM-1000V2 -
HORIBA, Ltd.
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
Wewon Environmental Chambers Co, Ltd.
Benchtop thermal forcing system from Wewon Environmental Chambers Co., Ltd. has a mini body structure and affordable machine price. The machine can test a wide temperature range, Since no compressor is required for refrigeration, so the benchtop temperature forcing unit’s energy consumption is very low. The repeated resistance degree of the tested sample in the instantaneous extremely high temperature and extremely low temperature continuous environment can detect the chemical changes and physical damage caused by thermal expansion and cold contraction of the sample in the shortest time, so as to achieve the goal of confirming the quality of the tested sample.https://www.wewontech.com/benchtop-thermal-forcing-system/
-
Entes Elektronik
LV power capacitors are circuit elements which compensate the inductive reactive loads on a system. Being able to connect and disconnect up to 100 times a day in accordance with load variations in automatic reactive power compensation systems really speaks for the quality and endurance and capacitors. Upon connection/disconnection instances, currents which have higher values than the nominal value may occur on reactive power compensation capacitors. ENTES ENT.C series power capacitors are designed to withstand the severe and poor conditions which may shorten the operating life during reactive power compensation. This endurance is the result of advanced engineering and long-term test procedures.
-
PXIe-1149.1/4E -
Corelis, Inc.
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
JTAG Technologies Inc.
Want to improve the overall test coverage of your assembled boards? It’s easy. Simply combine or integrate your JTAG Technologies boundary-scan tools with your existing automatic test equipment (ATE). We work with any vendor of in-circuit testers (ICT), flying probes (FPT) or functional testers (FT).We offer solutions for most of the available automatic test equipment systems, in addition we can support you with customized integrations for your existing automatic test equipment (ATE).
-
M5-2-COF -
Mark-10 Corp.
The M5-2-COF coefficient of friction (COF) gauge is an integral part of a COF testing system, typically including a motorized test stand and COF fixture. With a capacity of 2 lbF [10 N], the gauge can be used to measure friction for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients are displayed on the backlit LCD, and are calculated from a user-programmable sled weight.
-
4605-HTR -
TESEC, INC
4605-HTR is a MAP Sorter which picks up devices from wafer ring and sorts to tape or bin according to the MAP file created by film frame test handler or prober. 4605-HTR is a high speed handling system, available for 12 inches wafer rings. When used in combination with 4170-IH, 4605-HTR much improves efficiency in testing process of leadless devices as a high speed sorting machine.
-
60-106-002 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 60-106-002 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. It features remote control via USB or LXI Ethernet and this version of the chassis includes Scan List Sequencing & Triggering. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
AMETEK VTI Instruments
VTI is the first choice for mission critical applications or applications where the cost of test is high and failure is not an option. Applications include missile system testing and solid rocket motor testing. This is because our products are recognized in the industry for their reliability and are designed with built-in capabilities to maximize measurement confidence. Simply put, if you need equipment that is going to give you the results you need, contact us to get started.
-
X-COM Systems
Birds' line of Handheld RF Analyzers are rugged solutions for your field analysis needs. Ranging from the multi-functional SignalHawk Series and Spectrum Analyzers, to the SA Series, 25-6000 MHz Site Analyzers - a user-friendly test solution for installing, maintaining, and troubleshooting your antenna and cable systems, to the AT Series, Antenna Testers which provide a cost-effective, fast, graphical way of determining the quality of mobile and base station antennas.
-
Lead Connection -
Hanwell
A single channel data logger for temperature measurement with LCD display and fitted internal temperature sensor. This reliable transmitter is used with our renowned Hanwell Pro temperature humidity monitoring system for 24/7 data and instant alarm notifications. Contact us today for your free quotation and signal strength test (we can prove ours to be unrivalled) or to discuss your specific temperature monitoring requirements and application.
-
P014 -
AMETEK Sensors, Test & Calibration
The P014 hydraulic jack pump (System E) is an extremely effective pressure pump designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle.
